hi
i am newbie to linux.i am using redhat enterprise with kernel-2.6.9-42 and used this module usbat02-2.6-0.5.0 but didnot no work maybe i did not used it correctly.
I did the following steps:
1. I downloaded the source rpm for kernel 2.6.9-42.EL and rebuild it.
2. I patch the file present in usbat02-2.6-0.5.0/patch/usb-integration.patch.
3. replace the exixting usb.c and usb.h with the usbat02-2.6-0.5.0's usb.c and usb.h.
4. make menuconfig and select the option of USBAT/ support from USB mass storage option.
5. The setting are saved in new kernel and gave it the name usbat-2.6.9
6. Then use the command "make modules modules_install".
7. run "make install".
8. modprobe usb_storage
9. on demesg i got a meeage that i m sending.
Linux version 2.6.9-prep (root@localhost.localdomain) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 Wed Dec 5 02:24:17 PKT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fec0000 (usable)
BIOS-e820: 000000001fec0000 - 000000001fef8000 (ACPI data)
BIOS-e820: 000000001fef8000 - 000000001ff00000 (ACPI NVS)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
Using x86 segment limits to approximate NX protection
zapping low mappings.
On node 0 totalpages: 130752
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126656 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000ff980
ACPI: RSDT (v001 D815EA D815EPE2 0x20010918 MSFT 0x00001011) @ 0x1fef0000
ACPI: FADT (v001 D815EA EA81510A 0x20010918 MSFT 0x00001011) @ 0x1fef1000
ACPI: MADT (v001 D815EA EA81510A 0x20010918 MSFT 0x00001011) @ 0x1fee30e4
ACPI: DSDT (v001 D815E2 EA81520A 0x00000023 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:11 APIC version 17
Enabling APIC mode: Flat. Using 0 I/O APICs
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1ff00000:dfc80000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c0402000 soft=c0401000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1127.231 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 513968k/523008k available (2155k kernel code, 8444k reserved, 719k data, 164k init, 0k highmem)
Calibrating delay using timer specific routine.. 2275.22 BogoMIPS (lpj=1137612)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f3ff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) III CPU 1133MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 384k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 21 (level, low) -> IRQ 201
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1196822248.733:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports C1)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: AGP aperture is 64M @ 0xf8000000
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 17
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda
MA, hdb
io
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc
MA, hdd
io
Probing IDE interface ide0...
hda: ST340810A, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SONY CD-RW CRX320EE, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
hdc: ATAPI 52X DVD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 458752 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices:
PBTN PCI1 UAR1 USB USB2 AC9 SMB
Freeing unused kernel memory: 164k freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 4 roles, 355 types, 26 bools
security: 55 classes, 22582 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda7, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
inserting floppy driver for 2.6.9-prep
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 21 (level, low) -> IRQ 201
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0xd800, 00:50:ba:8b:eb:71, IRQ 201
eth0: Identified 8139 chip type 'RTL-8139C'
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 50662 usecs
intel8x0: clocking to 48000
hw_random: RNG not detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 177
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 177, io base 0000ef40
SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: detected 2 ports
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.9-prep uhci_hcd
usb usb1: SerialNumber: 0000:00:1f.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 193
uhci_hcd 0000:00:1f.4: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 193, io base 0000ef80
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1f.4: detected 2 ports
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.9-prep uhci_hcd
usb usb2: SerialNumber: 0000:00:1f.4
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
uhci_hcd 0000:00:1f.2: suspend_hc
uhci_hcd 0000:00:1f.4: suspend_hc
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0386d60(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ACPI: Power Button (FF) [PWRF]
EXT3 FS on hda7, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised:
dm-devel@redhat.com
cdrom: open failed.
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1044184k swap on /dev/hda8. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 already at revision 0x1c (current=0x1c)
microcode: No new microdata for cpu 0
IA-32 Microcode Update Driver v1.14 unregistered
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4086 buckets, 32688 max) - 356 bytes per conntrack
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: no IPv6 routers present
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
i2c /dev entries driver
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (polling).
lp0: console ready
uhci_hcd 0000:00:1f.4: port 1 portsc 0083
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
uhci_hcd 0000:00:1f.4: wakeup_hc
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
uhci_hcd 0000:00:1f.4: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new full speed USB device using address 2
uhci_hcd 0000:00:1f.4: uhci_result_control: failed with status 440000
[deeef240] link (1eeef1e2) element (1e59e040)
0: [de59e040] link (1e59e080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=0f5f36a0)
1: [de59e080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
uhci_hcd 0000:00:1f.4: uhci_result_control: failed with status 440000
[deeef240] link (1eeef1e2) element (1e59e040)
0: [de59e040] link (1e59e080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=0f5f36a0)
1: [de59e080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
usb 2-1: device not accepting address 2, error -71
uhci_hcd 0000:00:1f.4: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new full speed USB device using address 3
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: Product: DataTraveler 2.0
usb 2-1: Manufacturer: Kingston
usb 2-1: SerialNumber: 0F2195503303389E
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb-storage 2-1:1.0: usb_probe_interface
usb-storage 2-1:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x08ec, Product: 0x0008, Revision: 0x0100
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Kingston Model: DataTraveler 2.0 Rev: 1.04
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
USB Mass Storage device found at 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x9 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x9 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80000009 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
i am confused how would i know that i have installed the new driver for usbat02. Using lsmod shows usb_storage..(Used)with 0 before plugging the flash. and after plugging it turns to 1. what it means???
pls help me i am so confused how would i know that new module is loaded in my system
waiting 4 reply
